International Journal of Applied Electromagnetics and Mechanics - Volume 46, issue 3

Authors: Ro, Jong-Suk | Jung, Sang-Yong | Lee, Cheol-Gyun | Jung, Hyun-Kyo

Article Type: Research Article

Abstract: The important research area associated with the Ultra-Sonic Motor (USM) is the contact problem between the stator and the rotor. Because the USM operates by the friction force between the rotor and the stator, the contact problem of the USM have to be taken into account to analyze the motor performance accurately. Consequently, various types of the analysis methods have been proposed based on a contact model which describes the complex nonlinear contact condition of the …USM. In this paper, diverse types of contact analysis methods for a Travelling Wave Ultra-Sonic Motor (TWUSM) are clearly condensed and precisely examined. The governing equations for the analysis of the TWUSM performance are derived through a precise investigation of the relationship between the contact condition and the motor performance in this paper. Furthermore, the motor performance is analyzed using contact models and the calculated data are compared with the experimental results. Show more

Keywords: Analytical method, characteristic analysis, contact mechanism, traveling wave, ultrasonic motor

DOI: 10.3233/JAE-141745

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 437-453, 2014

Authors: Ding, Changjiang | Lu, Jun | Song, Zhiqing | Bao, Siqingaowa

Article Type: Research Article

Abstract: The aim of this work is to select the most suitable mathematical model to describe the thin layer electrohydrodynamic (EHD) drying of cooked beef based on voltage and such geometrical characteristics as thickness and cross-sectional area of the material. To accomplish this, the EHD drying technique was employed at 0 kV, 6 kV, 14 kV, 21 kV and 32 kV for alternating current (AC). The drying temperature was 21 ± 2°C, and the drying relative humidity …was 30 ± 5%, while the ambient wind speed was 0 m/s. Samples of cooked beef of different thickness and cross-sectional area were put into a high voltage electric field at 24 kV for AC. Six different mathematical drying models were then compared to simulate drying curves based on root mean square error, reduced mean square of deviation and modeling efficiency. The results showed that the drying rate of cooked beef was notably greater in the EHD system when compared to control. Both thickness and cross-sectional area of cooked beef had more impact on drying rate during the first half hour, and the Demir et al. model was the best mathematical model. Therefore, this work provides guidance for optimizing and improving the drying efficiency of EHD. Show more

Keywords: Electrohydrodynamic drying, moisture content, cooked beef, mathematical model

DOI: 10.3233/JAE-141781

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 455-461, 2014

Authors: Bu, Yinggang | Kinjo, Hideyuki | Oyaizu, Kazuaki | Inoue, Kaname | Mizuno, Tsutom | Duan, Zhihui

Article Type: Research Article

Abstract: A compact electro-magnetic oscillatory actuator was proposed based on a pair of torsion springs for optical scanners operating at low oscillating frequencies, such as 50 Hz for a portable barcode scanner. Each torsion spring in the actuator is made of silicone rubber and is dually supported at both ends. A yoke is coupled with the driven coil to enhance the driving torque of the actuator. In this study, we analyzed the effect of the yoke on the resonant …frequency of the actuator, as well as the torsion moment. We also experimentally determined the relationship between the resonant frequency and the magnetic gap of the yoke. Compared with the mechanical resonant frequency in the experiments, which was designed to be 50 Hz, the frequency was modified to 57.4 Hz, 54.7 Hz and 52.9 Hz when the gap between the yoke and the permanent magnet was 1.5 mm, 1.7 mm and 1.9 mm, respectively. The proposed actuator, which combines a yoke with flexible torsion springs, is potentially useful as a compact optical scanner, taking advantages of both low power consumption and high reliability. Show more

Keywords: Optical scanner, oscillatory actuator, torsion spring, silicone rubber, magnetic spring

DOI: 10.3233/JAE-141782

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 463-470, 2014

Authors: Dai, Jianguo | Chang, Siqin

Article Type: Research Article

Abstract: This paper presents the research on loss analysis of the electromagnetic linear actuator (ELA) with the purpose of performance improvement of ELA applied to the engine electromagnetic driven valve train (EDVT). To define ELA's loss distribution and variation, quantitative analysis has been carried out against ELA's loss composition and variation at different engine conditions through simulation of three-dimensional (3D) finite element. Meanwhile, in order to verify reliability of simulation model, locked-mover test …has been completed creatively. Then it analyzes the impact of flux density and excitation period on ELA's loss and thus some regular understandings are obtained. In the end, the result shows that the test data and simulating calculation agree well, and the error is less than 3.9%. Show more

Keywords: Electromagnetic linear actuator, loss, simulation, changes, locked-mover test

DOI: 10.3233/JAE-141783

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 471-482, 2014

Authors: Akdagli, Ali | Toktas, Abdurrahim | Bicer, Mustafa Berkan | Kayabasi, Ahmet | Ustun, Deniz | Kurt, Kasim

Article Type: Research Article

Abstract: In this work, a model constructed with the adaptive neuro – fuzzy inference system (ANFIS) for estimating the resonant frequency of rectangular ring compact microstrip antennas (RRCMAs) in UHF band is proposed. A total of 108 RRCMAs having different parameters related to the antenna dimensions and dielectric substrate were simulated with the help of electromagnetic packaged software IE3D™ based on method of moment (MoM) to generate the data pool for training and test processes of the …ANFIS model. While 96 RRCMAs were employed for training, the remainders were used for test the ANFIS model. The resonant frequencies were computed with the average percentage errors (APE) as 0.014% and 0.666% for training and test, respectively. The accuracy of proposed model was successfully demonstrated by comparing with the results of a method over the simulated data previously published in the literature. Further to inspect the validity of the ANFIS model, a RRCMA operating at 2.44 GHz was designed and fabricated for this work, and the accurate results concerning the resonant frequency were achieved. Show more

Keywords: Compact microstrip antennas, rectangular ring, resonant frequency, neuro-fuzzy, ANFIS

DOI: 10.3233/JAE-141784

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 483-490, 2014

Authors: Dhayalan, R. | Kumar, Anish | Rao, B. Purna Chandra | Jayakumar, T.

Article Type: Research Article

Abstract: This paper discusses finite element modeling of spiral coil electromagnetic acoustic transducer (EMAT) to generate bulk waves. First, a 2D electromagnetic model is developed for calculating the Lorentz force density, which is the driving force for sound wave generation within the material. Second, the calculated force at each point in the material is used as the driving force for generating sound wave modes. This model is used to predict the ultrasonic A-scan signals of bulk (longitudinal …and shear) waves in isotropic homogeneous material. Spiral coil EMATs of two different coil spacings are developed for experimental studies. The model predicted results are validated by experimental results and for this, the ratio of amplitude of shear wave to longitudinal wave is used. Show more

Keywords: Spiral coil EMAT, lorentz force density, finite element modeling, bulk waves

DOI: 10.3233/JAE-141933

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 491-500, 2014

Authors: Raval, Falguni | Kosta, Y.P. | Joshi, Harshita

Article Type: Research Article

Abstract: This paper discusses a triple-band microstrip circular antenna using rising sun shaped structure embedded in the substrate of patch antenna. The proposed design is based on the metamaterial property of rising sun shaped structure. The proposed antenna shows good performance at all resonant frequencies. The rising sun structure in substrate makes a major contribution to the first and second operating bands, while it has a minor effect on the third operating band. The proposed antenna is …compared with the conventional antenna. This antenna has a high gain at all working frequencies. The simulation results are analyzed and compared with the measured results, which shows that there is a good agreement between them. Show more

Keywords: Metamaterial, circular patch antenna, rising sun structure (RSS)

DOI: 10.3233/JAE-141934

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 501-509, 2014

Authors: Peng, Xiaoting | Zhan, Zaiji | Li, Zhixin

Article Type: Research Article

Abstract: Because of strong current, friction and arcing, electrical contact ablation occurs in the transmitting process of electromagnetic railgun, which is also one key issue in application. In this paper, an experimental apparatus is designed to detect electromagnetic railgun armature contacts ablation. Energy dispersive X-ray, scanning electron microscopy, high-resolution camera and rogowski coil are used to measure mass loss, volume change, the ablation layer analysis, the element distribution on ablation layer section and the …electrical contact analysis. Experimental results show that the input current and the contact pressure between electrodes are the major factors contributing to the ablation volume loss and mass loss. It is also showed that as a sliding electrode, the aluminum armature ablates more seriously during launch. Show more

Keywords: Railgun, electrical contact ablation, aluminum armature, experimental apparatus

DOI: 10.3233/JAE-141935

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 511-518, 2014

Authors: Rybin, Oleg

Article Type: Research Article

Abstract: The paper discusses microwave properties of the effective refractive index of two-component metamaterials with ferromagnetic metal inclusions. Here we study metamaterial media, which are presented as an infinite host dielectric material with periodically embedded ferrite-like metal cylindrical and spherical inclusions saturated with an external biasing magnetic dc field. The case when electromagnetic wave propagates transversely or parallel to the direction of biasing magnetic dc field is studied. Frequency ranges where the real …parts of effective refractive index of the metamaterials achieve unusual values (very small, much greater than unity etc.) were found. Show more

Keywords: Metamaterials, effective medium theory, inclusions, metaferrites, effective refractive index

DOI: 10.3233/JAE-141936

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 519-526, 2014

Authors: Yang, Xiao Qing | Zhai, Ying Ya | Xu, Chen | Jia, Guo Zhu

Article Type: Research Article

Abstract: Two different antipodal Vivaldi antennas design with better performances are proposed. The one is a small antipodal Vivaldi antenna for a 4.1–20 GHz frequency range, and its dimension is only 34 × 50 mm^{2} . Another proposed high gain antenna can achieve the maximum gain of 15.2 dBi within its operating band. Measured results of the manufactured antipodal Vivaldi antennas are in good agreement with the simulated ones. Besides the |S_{11}| , far field …radiation pattern, current distribution, phase, gain, and group delay which are important parameters of impulse distortion in ultra-wide band antenna are well analyzed. All results show that the proposed antipodal Vivaldi antennas have better performances and they are well suited for ultra-wide band communications. Show more

Keywords: Ultra-wide band, small antenna, high gain, Vivaldi antenna

DOI: 10.3233/JAE-141937

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 527-536, 2014

Authors: Tian, Wen-Yan | Wu, Ying-Chun | Li, Ze-Min | Dong, Zeng-Shou | Guo, Yi-Na | Luo, Ming

Article Type: Research Article

Abstract: A hybrid S-matrix is proposed based on artificial neural network (ANN) and Baum-Liu-Tesche (BLT) equations to analyze the electromagnetic interference (EMI) effects on PCB with active and passive circuit components. Transmission line equations and Finite difference time domain (FDTD) method are employed to compute the excited fields and extract the port parameters for passive printed circuits. ANN method is used to predict the S-parameters for some active components. Then, the trained ANN …model is combined with other S-parameters to compose a hybrid S-matrix for the characterization of the PCB. The resulting hybrid S-matrix and excited fields are subsequently exported to BLT equations to evaluate the responses. Examples are studied and the numerical results are compared with those obtained by experiment. The agreement is generally good that validates this method. Show more

Keywords: Hybrid S-matrix, artificial neural network (ANN), Baum-Liu-Tesche (BLT) equations

DOI: 10.3233/JAE-141938

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 537-545, 2014

Authors: Angiulli, G. | Cacciola, M. | Calcagno, S. | De Carlo, D. | Morabito, C.F. | Sgró, A. | Versaci, M.

Article Type: Research Article

Abstract: To efficiently solve the large, dense and non-Hermitian matrix system provided by the E-field Integral Equation (EFIE) modelization of the electromagnetic scattering by arbitrarily shaped perfect conducting bodies, the Generalized Minimal Residual method (GMRES) with preconditioning is usually employed. Nonetheless, even if optimal in a broad sense, the GMRES suffers of the drawback that its memory space demand grows linearly with the number of iterations. To avoid possible out-of-memory errors, a Krylov subspace method …involving a fixed amount of memory per iteration has to be used. This is the case of the Bi-Conjugate Stabilized (BiCGStab) method. Although this method has been exploited with success to handle dense matrix system arising from EFIE discretization, its flexible version, the Flexible-BiCGstab, at the best of the authors knowledge, has not received any attention within this context. In this work, a study on the performances of the Flexible BiCGStab to solve the discretized EFIE is presented. Numerical results demonstrate that the Flexible BiCGStab is, at least in the examined cases, a workable alternative to the the standard BiCGStab with ILUT preconditioning. Show more

Keywords: Electromagnetic scattering, integral equations, krylov subspace methods, method of moments

DOI: 10.3233/JAE-141939

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 547-553, 2014

Authors: Bahiraei, Mehdi | Hangi, Morteza

Article Type: Research Article

Abstract: This study has used the two-phase Euler-Lagrange method to evaluate the hydrothermal characteristics for a laminar flow of water-Mn_{0.6} Zn_{0.4}<FORMULA>Fe<FORMULA>_{2} O_{4} magnetic nanofluid in a circular pipe under the effect of magnetic field with both positive and negative gradients. Brownian and thermophoretic forces were considered in the simulation. Concentration distribution was found to be non-uniform at the cross section of the pipe, the value of which is greater in center of the …pipe than near wall. Non-uniformity in the concentration distribution will change the velocity profile under the application of magnetic field. Applying magnetic field with negative gradient increases the convective heat transfer coefficient, while decreases it in the case of positive gradient. Increasing the magnitude of magnetic field gradient causes a more considerable change in the convective heat transfer coefficient. In the presence of the magnetic field, the convective heat transfer coefficient also increases with increasing Reynolds number, concentration and particle size which the effects of magnetic field on heat transfer is less significant at higher Reynolds numbers. Moreover, the pressure drop increases in the case of applying magnetic field with negative gradient while applying the positive one would act as a pump and sucks the fluid from upstream. Show more

Keywords: Heat transfer, nanofluid, Mn-Zn ferrite, Euler-Lagrange, magnetic field

DOI: 10.3233/JAE-141955

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 555-567, 2014

Authors: Jung, Kwang Suk

Article Type: Research Article

Abstract: When a spiral-shaped, radial electrodynamic wheel with an axial pitch is rotated around a conductive rod, the magnetic field produced by the wheel can travel in the axial direction as well as in the circumferential direction of the wheel. Therefore, the rotating spiral wheel produces three-axial magnetic forces: a torque in the circumferential direction, a thrust force in the axial direction, and a repulsive force in the radial direction of the rod. These forces can be …used effectively in the contact-free conveyance of the conductive rod. In this paper, the magnetic forces produced by the spiral wheel are modeled theoretically, and the model is verified by FEM and experiment. And, desirable design specifications of the wheel are proposed by analyzing the influences of the pitch angle and the number of permanent magnets that govern the characteristics of the spiral wheel. However, the only parameter that influences the forces generated by the wheel is the rotation speed of the wheel. So, a control algorithm that varies only the rotating speed of the wheel to convey the conductive rod is proposed, and its feasibility is verified by application to a constructed set-up. Show more

Keywords: Contactless conveyance, radial electrodynamic wheel, independent control, spiral-shaped wheel

DOI: 10.3233/JAE-141956

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 569-582, 2014

Authors: Pal'a, Jozef | Bydžovský, Jan

Article Type: Research Article

Abstract: A simple method of measuring the Barkhausen noise in two stages was developed. The purpose of the proposed method was to remove the magnetizing frequency component from the induced electromotive force signal without using complex analog or digital filters, which also suppress the Barkhausen noise. In the first stage, an instance of the electromotive force signal was temporarily recorded, and in the second stage another instance of the electromotive force signal subtracted from the previously recorded …instance of the electromotive force signal was measured. Using this method we will obtain only the stochastic component of the electromotive force signal – the Barkhausen noise. The method is illustrated on measuring the Barkhausen noise in an electrical steel sample. The experiments proved that with this method we are able to remove the dominant continuous component from the induced electromotive force signal and we can simplify the measurement. The general problems associated with the method are discussed. Show more

Keywords: Barkhausen noise, electromotive force signals subtraction, two-stage measuring method

DOI: 10.3233/JAE-141957

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 583-591, 2014

Authors: Zhao, Yong | Li, Hao | Lv, Ri-Qing | Hu, Hai-Feng

Article Type: Research Article

Abstract: Magnetic fluid was a novel functional material with many unique properties, especially in the case that the magnetic field was applied. It was found that the special properties of magnetic fluid were determined by its unique microstructure. Then, the special properties could be understood fundamentally by researching the extraordinary nature of the microstructure of the magnetic fluid. At the same time, it was a good theoretic guidance for the experimental research on the properties of magnetic …fluid to make clear about the microstructure model theoretically. Therefore, it was particularly important to study the simulation methods to obtain the microstructure of magnetic fluid. The development of the microstructure simulation methods of magnetic fluid were introduced in this article, and the basic principles of various simulation methods were expounded in detail. The features of each microstructure simulation methods of magnetic fluid were summarized and compared with each other. Finally, the key problems and research direction of the numerical simulation method in the future were described. Show more

Keywords: Magnetic fluid, magnetic field, microstructure, simulation methods

DOI: 10.3233/JAE-141958

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 593-610, 2014

Authors: Ashraf, Muhammad A. | Rizvi, Azhar A.

Article Type: Research Article

Abstract: Total scattering cross section (σ_T ) of a PEC cylindrical scatterer is a function of it's scattering amplitude and is closely related to scatterer's cross section. It is difficult to determine σ_T analytically for arbitrary cross sections of scatterer, especially for random cross sections. Defining some bounds on the value of σ_T is therefore very helpful in its estimation. In this paper, σ_T of canonical shaped …objects is used to define bounds on σ_T of random cylinder. The geometrical parameters of canonical scatterers are obtained from the geometric parameters of the random cylinder. A formulation is also developed to approximate the value of σ_T from its bounding values. This work therefore, helps to predict the σ_T of a random cylinder from its geometrical parameters, without solving an electromagnetic boundary value problem. Show more

Keywords: Random cylinder, total scattering cross section, equivalent area, equivalent perimeter

DOI: 10.3233/JAE-141959

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 611-618, 2014

Authors: Torkaman, Hossein

Article Type: Research Article

Abstract: The performance of the Switched Reluctance Motors (SRMs) in different applications has widely been investigated by various studies. The research areas are oriented toward fault effects on electromagnetics behavior and its diagnosis for operation improvement. One of the most observed faults is the stator winding short circuit which may lead to produce the unbalanced distribution of magnetic field. In this paper, it is attempted to firstly introduce the conventional SRM and new structure of double stator …SRM (DSSRM). Secondly, by means of three dimensional finite element method (3D FEM) the effects of short-circuit faults (SCF) on motor profiles are investigated, in which static and dynamic behaviors of the motor in healthy and several SCF conditions are evaluated. A new method namely as maximum current point tracking (MCPT) is introduced to evaluate the SCF in SRM, so an index is proposed to detect the numbers of shorted turns in faulty phase. The overall outcomes highlight the advantages of using this method and index which is general enough to be applied to any type of SRM. Show more

Keywords: Switched reluctance motor, electromagnetics analysis, fault analysis, short circuit fault, maximum current point tracking

DOI: 10.3233/JAE-141960

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 619-628, 2014

Authors: El Dhaba, A.R. | Ghaleb, A.F. | El-Seadawy, J. | Abou-Dina, M.S.

Article Type: Research Article

Abstract: The static, uncoupled problem of thermomagnetoelasticity for long cylinders carrying a steady, axial current is investigated in stresses within a numerical approach by a boundary integral method in terms of real harmonic functions.This is the numerical realization of the field equations, boundary conditions and other relations presented in [1]. The method is complemented by the use of boundary collocation method to evaluate some path-independent line integrals needed in the representation of the mechanical displacement field. …The material of the cylinder is assumed homogeneous and isotropic, and linear dependence of the magnetic permeability on strain is taken in consideration through two material constants. Formulae are obtained for the boundary values of functions of practical interest like stress and mechanical displacement. Evaluation in the bulk may then be carried out by quadrature on the basis of well-known formulae of the theory of potential. The special case of an elliptic boundary is treated and the results are compared to the analytical solution established in [11]. It is concluded that the proposed numerical scheme performs efficiently in this case, and may thus be used for other forms of the boundary, subject only to smoothness condition. Show more

Keywords: Plane problem, thermo-magnetoelasticity, electric current, magnetic field, thermomagnetic stresses, Maxwell stress, boundary method, boundary integrals, numerical methods

DOI: 10.3233/JAE-141961

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 629-648, 2014

Authors: Yang, J.S. | Tiersten, H.F.

Article Type: Research Article

Abstract: The equation for transversely varying thickness modes in doubly-rotated quartz resonators is applied in the analysis of the vibrations of contoured resonators with beveled cylindrical edges. The treatment in this work differs from that of earlier work in that the dominant condition at the edge of the resonator is satisfied and the approximation made earlier in the beveled annulus is not made here where the solution is exact. A procedure for the analytical determination of the …required diameter for a good resonator is identified and calculated results are compared with those of the earlier work. Show more

Keywords: Piezoelectric, resonator, vibration

DOI: 10.3233/JAE-141962

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 649-661, 2014

Authors: Yuan, Qian | Han, Bangcheng | Dong, Baotian

Article Type: Research Article

Abstract: In order to find an algorithm to get a better optimization result of high-speed rotor supported by magnetic bearing in BLDCM, we presented a multiple objective optimization results which included three algorithms' in this paper. They are the local Sequential Quadratic Program (SQP) algorithm, the global Genetic Algorithm (GA) and the combined optimization strategy algorithm which combines GA and SQP. The parametric optimization model of a 100 kW BLDCM supported by magnetic bearings was constituted with …software ANSYS and an effective connection between software ANSYS and iSIGHT was used to execute the whole optimization process. To insure the best performance, mass and strength were chosen as the optimization goals, meanwhile, the static strength, dynamic modal, shape and magnetic force of the rotor subassembly were used as the main constrains. Six main dimensions of the subassembly were optimized. The optimization results indicated that the GA can get a higher optimization precision than the other two algorithms and the SQP was not effective in the optimization of magnetic suspended motor rotor subassembly. The GA's optimization result made the mass decrease 7.62 percent with the safe factor is 3.15. The 100 kW BLDCM supported by magnetic bearings was designed and fabricated; the multiple objective optimization results were verified by the prototype. Show more

Keywords: Magnetic suspension motor, optimization, genetic algorithm, combined optimization strategy, static strength and dynamic modal

DOI: 10.3233/JAE-141963

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 663-673, 2014

Authors: Arehpanahi, Mehdi | Jamal, Naser Saberi

Article Type: Research Article

Abstract: In this paper, a new sampling point refinement for saturation modeling in Surface Current Method (SCM) is proposed. In this method the variable permeability inside the magnetic materials due to the saturation is defined by optimization of sampling point number and their positions. In other words, the sampling points inside the material are refined for any current value and air gap variation. These results depend on magnetic energy of sampling points inside the material and the …value of them is strongly depend on sampling point positions. Simulation results verification have been done with the FEM. Show more

Keywords: Saturation, surface current method, magnetic devices, permeability, boundary and magnetic energy

DOI: 10.3233/JAE-141964

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 675-681, 2014

Authors: Taherdangkoo, Mohammad | Taherdangkoo, Reza

Article Type: Research Article

Abstract: We propose a new method for solving the Loney's solenoid benchmark problem based on Blind, Naked Mole-Rats (BNMR) algorithm. The key idea of the algorithm is using a \beta -distribution that can efficiently achieve the best solution for the position and size of two correcting coils in the famous Loney's solenoid problem. The results show the superiority of the proposed method on other previously methods for electromagnetic optimization.

Keywords: Modified BNMR algorithm, Loney's solenoid problem, β-distribution

DOI: 10.3233/JAE-141965

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 683-692, 2014

Authors: Li, Peng | Jin, Feng

Article Type: Research Article

Abstract: The thickness-shear modes in a circular cylindrical piezoelectric transformer considering the effect of an epoxy-bonded layer are analyzed, and an exact solution is obtained from the equations of the linear theory of piezoelectricity. Systematic parametric studies are subsequently carried out to quantify the effects of the epoxy-bonded layer upon the transformer performance, including its thickness, elastic coefficient and mass density. It is demonstrated that whilst the thickness and elastic coefficient of the layer …affect significantly the resonance frequencies, transforming ratio, power density, admittance and efficiency, and its mass density has negligible influence. On condition that the thickness of the epoxy layer is vanishingly small so that it degenerates into the solution by the classical shear-lag model. Upon comparing with the predictions obtained by employing the traditional shear-lag model, it is found that the interface viscous damping is absolutely due to the elastic coefficient of the epoxy layer, and the present structure model is found to be more accurate especially when the thickness of the epoxy layer can not be neglected. Show more

Keywords: Thickness-shear mode, cylindrical piezoelectric transformer, epoxy-bonded layer, shear-lag model, viscous damping

DOI: 10.3233/JAE-141966

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 693-708, 2014

Authors: Xu, Lizhong | Li, Huaiyong

Article Type: Research Article

Abstract: The Authors propose an electromechanical integrated harmonic piezodrive system. The dynamics behavior of the movable tooth drive has important effects on its operating performance. Here, the dynamic equations of the movable tooth drive for the drive system are presented. Using the equations, the natural frequencies and vibrating modes of the movable tooth drive are investigated. Results show that five vibrating modes occur for the movable tooth drive which include system modes, static crown gear modes, …movable tooth modes, translating rotor modes and translating crown gear modes. Eccentric center, thickness and length of the flexible ring, diameter of the movable tooth and speed ratio have significant effects on the natural frequencies of the movable tooth drive and should be selected properly. Show more

Keywords: Electromechanical integrated, harmonic piezodrive, vibrating modes, natural frequency

DOI: 10.3233/JAE-141967

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 709-726, 2014

Authors: Lin, X.J. | Huang, K.M. | Yang, Y.

Article Type: Research Article

Abstract: For the study of microwave chemistry, it is necessary to develop a reactor with small-size and wide operating frequency band. This paper presents a novel microwave coaxial reactor. Its main part is a coaxial cavity, and the input end is a coaxial port filled with PTFE, and the other end is a short circuit terminal. Two orifices which are designed as cut-off waveguides for microwave are attached to the cavity as passageway of sample solutions, so the …reactor can treat the samples continuously. The distributions of electromagnetic field and temperature of this novel microwave coaxial reactor used for heating edible vegetable oil at 915 MHz and 2450 MHz are simulated with finite-element method multi-fields coupling analysis. It is easy to find out that this novel microwave coaxial reactor could work properly over a wide frequency band. Also, the operating frequency could be chosen over a wide frequency band to get the optimal reaction effect to meet the requirements of experiments. Show more

Keywords: Microwave chemistry, coaxial, numerical simulation, heating

DOI: 10.3233/JAE-141969

Citation: International Journal of Applied Electromagnetics and Mechanics, vol. 46, no. 3, pp. 727-737, 2014